@ -40,35 +40,39 @@ Selects which tuner is used for input. For RSPduo this can be 1 or 2. Other RSP
@@ -40,35 +40,39 @@ Selects which tuner is used for input. For RSPduo this can be 1 or 2. Other RSP
Selects which antenna port is used. The antenna ports available depend upon the RSP device and tuner selected.
<h3>7: DC offset correction</h3>
<h3>7. Transverter mode open dialog</h3>
This button opens a dialog to set the transverter mode frequency translation options. The details about this dialog can be found [here](../../../sdrgui/gui/transverterdialog.md)
<h3>8: DC offset correction</h3>
Check this button to enable DC offset correction.
<h3>8: IQ imbalance correction</h3>
<h3>9: IQ imbalance correction</h3>
Check this button to enable IQ imbalance correction.
<h3>9: External reference clock output</h3>
<h3>10: External reference clock output</h3>
Enable reference clock output. This is only available for RSP2 and DSPduo.
<h3>10: Bias tee</h3>
<h3>11: Bias tee</h3>
Enable bias tee. This is only available for RSP1A, RSP2, RSPduo tuner 2 and RSPdx.
<h3>11: AM notch filter</h3>
<h3>12: AM notch filter</h3>
Enable AM notch filter. This is only available for RSPduo tuner 1.
<h3>12: MW/FM notch filter</h3>
<h3>13: MW/FM notch filter</h3>
Enable MW/FM notch filter. This is only available for RSP1A, RSP2, RSPduo and RSPdx.
<h3>13: DAB notch filter</h3>
<h3>14: DAB notch filter</h3>
Enable DAB notch filter. This is only available for RSP1A, RSPduo and RSPdx.
<h3>14: IF bandwidth</h3>
<h3>15: IF bandwidth</h3>
This selects the IF filter bandwidth. The following bandwidths are available:
@ -81,31 +85,49 @@ This selects the IF filter bandwidth. The following bandwidths are available:
@@ -81,31 +85,49 @@ This selects the IF filter bandwidth. The following bandwidths are available:
- 7000 kHz
- 8000 kHz
<h3>15: IF frequency</h3>
<h3>16: IF frequency</h3>
Warning there is no good support of non zero IF. **It is advised to keep zero IF for normal use**.
Some tricks are provided for expert use of non-zero IFs. You may want to start from these settings to experiment more with it.
This selects the IF frequency between these values:
- **0 for zero IF**
- 450 kHz. Some practical tricks that may or may not work:
- Frequency is shifted by -450 kHZ.
- Do not set center frequency lower than 450 kHz down the target frequency
- Use at least 1536 kHz bandwidth (14)
- After sample rate change (16) you may need to start/stop device to get thins right.
- Use decimation > 1 (17) with Inf position (18)
- 1620 kHz: do not use
- 2048 kHz: do not use
<h3>16: Sample rate</h3>
- 450 kHz.
- Move center frequency by -450 kHZ (3).
- Direct frequency reading is -450 kHz off from real Rx frequency.
- You may use the transverter mode (7) with a shift of +450 kHz to correct the frequency reading
- If you already use the transverter mode for transverter work just add 450 kHz to the current shift
- Use 1536 kHz bandwidth (15)
- After sample rate change (17) you may need to start/stop device to get things right.
- Use decimation > 1 (18) with Inf position (19)
- 1620 kHz:
- Move center frequency by -1620 kHz (3).
- Direct frequency reading is -1620 kHz off from real Rx frequency.
- You may use the transverter mode (7) with a shift of +1620 kHz to correct the frequency reading
- If you already use the transverter mode for transverter work just add 1620 kHz to the current shift
- Use 5000 kHz bandwidth (15)
- After sample rate change (17) you may need to start/stop device to get things right.
- Use decimation > 1 (18) with Inf position (19)
- 2048 kHz:
- Move center frequency by -2048 kHz (3).
- Direct frequency reading is -2048 kHz off from real Rx frequency.
- You may use the transverter mode (7) with a shift of +2048 kHz to correct the frequency reading
- If you already use the transverter mode for transverter work just add 2048 kHz to the current shift
- Use 5000 kHz bandwidth (15)
- After sample rate change (17) you may need to start/stop device to get things right.
- Use decimation > 1 (18) with Inf position (19)
<h3>17: Sample rate</h3>
Sets the ADC IQ sample rats from 2M to 10.66M Hz.
<h3>17: Decimation</h3>
<h3>18: Decimation</h3>
Decimation in powers of two from 1 (no decimation) to 64.
<h3>18: Decimated bandpass center frequency position relative the SDRplay center frequency</h3>
<h3>19: Decimated bandpass center frequency position relative the SDRplay center frequency</h3>
- **Cen**: the decimation operation takes place around the SDRplay center frequency Fs.
- **Inf**: the decimation operation takes place around Fs - Fc.
@ -116,14 +138,14 @@ With SR as the sample rate before decimation Fc is calculated as:
@@ -116,14 +138,14 @@ With SR as the sample rate before decimation Fc is calculated as:
- if decimation n is 4 or lower: Fc = SR/2^(log2(n)-1). The device center frequency is on the side of the baseband. You need a RF filter bandwidth at least twice the baseband.
- if decimation n is 8 or higher: Fc = SR/n. The device center frequency is half the baseband away from the side of the baseband. You need a RF filter bandwidth at least 3 times the baseband.
<h3>19. RF gain setting</h3>
<h3>20. RF gain setting</h3>
Sets the LNA and mixer gain dB. The settings available depended upon the RSP device and frequency band.
<h3>20. IF AGC</h3>
<h3>21. IF AGC</h3>
Check this button to enable IF automatic gain control.
<h3>21. IF gain</h3>
<h3>22. IF gain</h3>
Manual IF gain from 0 to -59 dB. Only enabled when IF AGC is disabled.