diff --git a/doc/img/TestSourceInput_plugin.png b/doc/img/TestSourceInput_plugin.png index 3ad8b3630..a81b23a0a 100644 Binary files a/doc/img/TestSourceInput_plugin.png and b/doc/img/TestSourceInput_plugin.png differ diff --git a/doc/img/TestSourceInput_plugin.xcf b/doc/img/TestSourceInput_plugin.xcf index c34ff4fc7..d779f7edf 100644 Binary files a/doc/img/TestSourceInput_plugin.xcf and b/doc/img/TestSourceInput_plugin.xcf differ diff --git a/doc/img/TestSourceInput_plugin_2.png b/doc/img/TestSourceInput_plugin_2.png new file mode 100644 index 000000000..d5ad59be0 Binary files /dev/null and b/doc/img/TestSourceInput_plugin_2.png differ diff --git a/doc/img/TestSourceInput_plugin_2.xcf b/doc/img/TestSourceInput_plugin_2.xcf new file mode 100644 index 000000000..77e4e065b Binary files /dev/null and b/doc/img/TestSourceInput_plugin_2.xcf differ diff --git a/plugins/samplesource/testsource/readme.md b/plugins/samplesource/testsource/readme.md index 3d31d8a50..b357c6f16 100644 --- a/plugins/samplesource/testsource/readme.md +++ b/plugins/samplesource/testsource/readme.md @@ -36,22 +36,25 @@ Record baseband I/Q stream toggle button Baseband I/Q sample rate in kS/s. This is the device to host sample rate (3) divided by the decimation factor (4). -

2: Auto correction options

+

2: Various options

-These buttons control the local DSP auto correction options: +![Test source input plugin GUI 2](../../../doc/img/TestSourceInput_plugin_2.png) - - **DC**: auto remove DC component - - **IQ**: auto make I/Q balance. The DC correction must be enabled for this to be effective. +

2.1: Auto corrections

-

3: Carrier shift from center frequency

+This combo box control the local DSP auto correction options: -Use this control to set the offset of the carrier from the center frequency of reception. + - **None**: no correction + - **DC**: auto remove DC component + - **DC+IQ**: auto remove DC component and correct I/Q balance. -

4: Decimation factor

+

2.2: Decimation factor

The I/Q stream from the generator is doensampled by a power of two before being sent to the passband. Possible values are increasing powers of two: 1 (no decimation), 2, 4, 8, 16, 32. This exercises the decimation chain. -

5: Baseband center frequency position relative the center frequency

+This exercises the decimation chain. + +

2.3: Baseband center frequency position relative the center frequency

Possible values are: @@ -59,44 +62,60 @@ Possible values are: - **Inf**: the decimation operation takes place around the center of the lower half of the BladeRF Rx passband. - **Sup**: the decimation operation takes place around the center of the upper half of the BladeRF Rx passband. -This exercises the decimation chain. - -

6: Sample rate

- -This controls the generator sample rate in samples per second. - -

7: Sample size

+

2.4: Sample size

This is the sample size in number of bits. It corresponds to the actual sample size used by the devices supported: - **8**: RTL-SDR, HackRF - **12**: Airspy, BladeRF, LimeSDR, PlutoSDR, SDRplay - **16**: Airspy HF+, FCD Pro, FCD Pro+ - -

8: Amplitude coarse control

-This slider controls the number of amplitude bits by steps of 100 bits. +

3: Sample rate

+ +This controls the generator sample rate in samples per second. + +

4: Modulation

+ + - **No**: No modulation + - **AM**: Amplitude modulation (AM) + - **FM**: Frequency modulation (FM) -

9: Number of amplitude bits

+

5: Modulating tone frequency

+ +This controls the modulating tone frequency in kHz in 10 Hz steps. + +

6: Carrier shift from center frequency

-This is the signal peak amplitude in number of bits +Use this control to set the offset of the carrier from the center frequency of reception. -

10: Amplitude fine control

+

7: AM modulation factor

+ +This controls the AM modulation factor from 0 to 99% -This slider controls the number of amplitude bits by steps of 1 bit. +

8: FM deviation

+ +This controls the frequency modulation deviation in kHz in 100 Hz steps. It cannot exceed the sample rate. -

11: Signal power

+

9: Amplitude coarse control

-This is the signal power in dB relative to the maximum power (full bit range). +This slider controls the number of amplitude bits by steps of 100 bits. The total number of amplitude bits appear on the right. + +

10: Amplitude fine control

-

12: DC bias

+This slider controls the number of amplitude bits by steps of 1 bit. The signal power in dB relative to the maximum power (full bit range) appear on the right. + +

11: DC bias

Use this slider to give a DC component in percentage of maximum amplitude. -

13: I bias

+

12: I bias

Use this slider to give an in-phase (I) bias in percentage of maximum amplitude. -

14: Q bias

+

13: Q bias

+ +Use this slider to give an quadrature-phase (Q) bias in percentage of maximum amplitude. + +

14: Phase imbalance

-Use this slider to give an quadrature-phase (Q) bias in percentage of maximum amplitude. \ No newline at end of file +Use this slider to introduce a phase imbalance in percentage of full period (continuous wave) or percentage of I signal injected in Q (AM, FM).