@ -8,10 +8,10 @@ These packets can contain flight plans and other operational data as well as sta
@@ -8,10 +8,10 @@ These packets can contain flight plans and other operational data as well as sta
ACARS uses MSK modulation at 2,400 baud, which is then AM modulated on to the VHF carrier.
In Europe, the main ACARS frequencies are:
- 131.525 MHz (SITA - Europe secondary)
- 131.525 MHz (SITA - Europe secondary)
- 131.725 MHz (SITA - Europe primary)
- 131.825 MHz (ARINC/Collins)
VDL Mode 2 uses D8PSK modulation at 10,500 baud (bit rate 31,500 bps). It can contain ACARS or ATN packets.
VDL Mode 2 frequencies in Europe are:
@ -24,7 +24,7 @@ VDL Mode 2 frequencies in Europe are:
@@ -24,7 +24,7 @@ VDL Mode 2 frequencies in Europe are:
- 136.900 MHz
- 136.975 MHz (SITA & ARINC, the common signalling channel)
HFDL uses M-PSK at 1,800 baud and frequencies are between 2 and 21 MHz. The active frequencies vary with propagation, and the
HFDL uses M-PSK at 1,800 baud and frequencies are between 2 and 21 MHz. The active frequencies vary with propagation, and the
frequencies in use are reported in squitters transmitted by the ground stations. These are combined by the demodulator and
displayed in the Ground Station Table dialog. You can find an initial frequency to try on: https://hfdl.observer/
@ -82,7 +82,7 @@ Average total power in dB relative to a +/- 1.0 amplitude signal received in the
@@ -82,7 +82,7 @@ Average total power in dB relative to a +/- 1.0 amplitude signal received in the
<h3>4: Mode and Aero rate</h3>
Selects the demodulator: ACARS, VDL-2, HFDL, Aero or Iridium - and, in Aero mode
only, the rate and channel selector appears beside it.
only, the rate and channel selector appears beside it.
Changing either resets the demodulator and sets a default RF bandwidth.
Each demodulator runs at its own fixed channel sample rate, which the channelizer is
@ -100,7 +100,7 @@ set to when the mode is selected.
@@ -100,7 +100,7 @@ set to when the mode is selected.
<h3>5: RF Bandwidth</h3>
This specifies the bandwidth of a LPF that is applied to the input signal to limit the RF bandwidth.
This specifies the bandwidth of a LPF that is applied to the input signal to limit the RF bandwidth.
A default value is automatically set when selecting the Mode, and in Aero mode the rate
and channel, from the combo boxes (4):
@ -227,7 +227,7 @@ parts have arrived - and the selected block.
@@ -227,7 +227,7 @@ parts have arrived - and the selected block.
* Block Seq. - For multipart downlinks, the block sequence character used to order the blocks.
* Flight - For downlinks, the six-character flight identifier carried in the message text header.
* Message - The ACARS message payload after the standard downlink header fields and any recognized sublabel have been removed.
* Message Decode - A structured, human-readable decode of the message payload.
* Message Decode - A structured, human-readable decode of the message payload.
Selecting the row displays the full multi-line
decode below the table.
* ATC - Air Traffic Control communication extracted from supported ARINC 622/CPDLC messages.
@ -246,7 +246,7 @@ have no ACARS header, so only the following columns are used:
@@ -246,7 +246,7 @@ have no ACARS header, so only the following columns are used:
* Date/Time - The receiver's local date and time when the frame was received.
* Dir - The transmission direction. An up arrow is an uplink to an aircraft; a down arrow is a downlink from an aircraft.
* GS - Ground Station Id.
* GS - Ground Station Id.
* GS Decode - Ground Station name.
* Registration - The aircraft side of the link. VDL-2 link frames identify aircraft by their 24-bit ICAO address (the same address the aircraft transmits in Mode S / ADS-B) rather than by registration, so the registration is looked up from the OpenSky database (14); when the address is not in the database, the address itself is shown in hexadecimal. Frames between ground stations show `GS` followed by the ground station's address, and broadcasts show `All`.
* Label - The AVLC frame type: `I` (information), `UI`, `XID` (link management, including GSIF ground station broadcasts), `TEST`, or the supervisory types `RR`, `RNR`, `REJ`, `SREJ`, `DM`, `DISC`, `UA`, `FRMR`.
@ -260,7 +260,7 @@ have no ACARS header, so only the following columns are used:
@@ -260,7 +260,7 @@ have no ACARS header, so only the following columns are used:
<h3>HFDL Frames</h3>
HFDL frames that are not carrying an ACARS message use the same columns as the VDL-2 link frames.
HFDL frames that are not carrying an ACARS message use the same columns as the VDL-2 link frames.
<h3>Aero Signal Units</h3>
@ -271,7 +271,7 @@ units that are not carrying an ACARS message use only the following columns:
@@ -271,7 +271,7 @@ units that are not carrying an ACARS message use only the following columns:
* Dir - The transmission direction. An up arrow is a transmission from the ground earth
station on a P channel; a down arrow is a transmission from an aircraft on an R or T
channel.
* GS - Ground Earth Station (GES) Id.
* GS - Ground Earth Station (GES) Id.
* GS Decode - Satellite name, for example 'AOR-E'. See frequency table above.
* Registration - The aircraft, when the signal unit names one. The AES ID is the
aircraft's 24-bit ICAO address - the same address it transmits in Mode S / ADS-B.
@ -107,11 +107,11 @@ an ATC style; when unchecked just the callsign or registration is shown.
@@ -107,11 +107,11 @@ an ATC style; when unchecked just the callsign or registration is shown.
<h3>6: Statistics</h3>
The statistics table can be shown and hidden with the statistic button.
The statistics table can be shown and hidden with the statistic button.
Right click the button to reset the records.
Every figure is given twice, side by side: for this session and for all time, each with
who set it and when.
who set it and when.
* **Maximum range**, one row per protocol - the furthest aircraft heard on ADS-B, ACARS,
VDL-2, HFDL and Aero. Per protocol rather than as one figure because the protocols are
@ -195,7 +195,7 @@ Click to open the settings dialog.
@@ -195,7 +195,7 @@ Click to open the settings dialog.
This allows aircraft to be kept forever, but only their
recent flights - which hold the tracks, profiles and ACARS documents, so are most of the
database. An aircraft's most recent flight is always kept. Zero keeps flights for as long
as their aircraft.
as their aircraft.
* ADS-B position for (mins) - how long an aircraft stays on the Map after its last ADS-B
position
* ACARS position for (mins) - the same for a position from ACARS, VDL-2, HFDL, Aero or Iridium.
@ -210,7 +210,7 @@ Unticked ones are ignored.
@@ -210,7 +210,7 @@ Unticked ones are ignored.
**Use airline callsigns in Map labels** - writes the flight on the Map the way it is
spoken on the radio rather than the way it is transmitted: SPEEDBIRD 123 instead of
BAW123, using the airline's radio callsign from the airline database.
BAW123, using the airline's radio callsign from the airline database.
**Show the maximum range record on the Map** - keeps the aircraft that set the all time
maximum range record permanently on the Map, drawn at the position it was in when it set
@ -221,7 +221,7 @@ reset, or this is turned off.
@@ -221,7 +221,7 @@ reset, or this is turned off.
**Favour airline livery over aircraft type (3D map)** - when no 3D model exists of the
right type in the right livery, prefer a similar aircraft in the correct livery over an
exact type in the wrong one.
exact type in the wrong one.
**Livery aircraft icons (2D map)** - display aircraft on the 2D map using icons showing
@ -1049,7 +1049,7 @@ void RemoteTCPInputTCPHandler::processDecompressedZlibData(const char *inBuf, in
@@ -1049,7 +1049,7 @@ void RemoteTCPInputTCPHandler::processDecompressedZlibData(const char *inBuf, in
// Ensure conversion buffer is large enough - FIXME: Don't use this buffer - just write in to FIFO
if(nbSamples>(int)m_converterBufferNbSamples)
{
if(m_converterBuffer)
if(m_converterBuffer)
{
delete[]m_converterBuffer;
m_converterBuffer=nullptr;
@ -2323,7 +2323,7 @@ void RemoteTCPInputTCPHandler::processUncompressedData(const char *inBuf, int nb
@@ -2323,7 +2323,7 @@ void RemoteTCPInputTCPHandler::processUncompressedData(const char *inBuf, int nb