New channel Tx plugin modchirpmodem, built on libchirpmodem (format v1),
modelled on modpacket: plugin, settings, baseband, source, GUI, web API
adapter, readme.
- A transmission is the message's frames, separated by a gap, then a CW ID
with the source callsign. It is generated in full on a one-thread
generator pool, never on the DSP thread, and posted back to the baseband;
the source plays it out at the channel rate. A result made for an old
channel rate or offset is generated again; one on air when the rate or
offset changes is cut off and reported.
- Policy is libchirpmodem's: a licensed frame without a source callsign is
refused (EPOLICY) and CW ID above 20 WPM is rejected; no encryption
option. CW ID can be turned off in the licensed profile, with a warning in
the GUI and the report. The unlicensed profile is shown in red.
- Settings: SF, BW, payload mode, profile, src, dst, message, repeat, gap,
amplitude, CW ID and its speed. The GUI shows airtime per frame and the
largest body that fits (chirpmodem_frame_seconds, chirpmodem_max_body).
- Web API / MCP: ChirpModemMod.yaml (settings, report, actions), SWG
classes, ChannelSettings/Report/Actions and model factory entries cloned
from PacketMod (plain setters, safe in the request mapper's reset lists),
webapiutils, webapirequestmapper, webapi.qrc. Action {"tx": 1} with
optional src, dst and message for one transmission.
- Channelizer asked for 4 x BW, as chirpmodem_tx_new needs fs >= 2.2 x
(BW/2 + |IF|) and the channelizer leaves a residual offset.
Verified: FileOutput -> cm_rx 3/3 frames, +17.4 dB, 0.0 Hz; FileOutput ->
FileInput -> demodchirpmodem 3/3 in get_packets; over the air (Pluto at
-30 dB through 40 dB to an RTL-SDR, 223.58 MHz) 15/15 frames received by
demodchirpmodem, matching cm_rx on SDRangel's recording of the same signal
(+17.0 dB, -2713 Hz).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
New channel Rx plugin demodchirpmodem, built on libchirpmodem (format v1),
modelled on demodselcal: plugin, settings, baseband, sink, GUI, web API
adapter, readme. Rx only.
- The channel is decimated to at least 2 x BW; the library is given the
delivered rate and the signal's residual offset in it (if_offset).
- The chirpmodem_rx handle lives in the sink and is used only on the
baseband thread under the baseband mutex. Settings changes mark it stale;
it is rebuilt once per message, never during chirpmodem_rx_push().
- Frames are copied in the callback and posted to the channel, which
forwards them to the GUI and publishes OK frames (whole MAC frame) on the
"packets" pipe.
- GUI: SF, BW, effort, auto effort, report failures, max bytes; frames table
(UTC, status, profile, src, dst, SNR, offset Hz/ppm, mode, length, text,
hex) with licensed-profile policy flag; channel spectrum.
- libchirpmodem found with find_package(chirpmodem 0.1 REQUIRED), hint
CHIRPMODEM_DIR or ~/.local; linked statically. Builds in SERVER_MODE.
Web API / MCP support:
- ChirpModemDemod.yaml (settings and report), SWG model classes, entries
in SWGChannelSettings/SWGChannelReport/SWGModelFactory, webapiutils,
webapirequestmapper and webapi.qrc.
- MCP data feed: listen to sdrangel.channel.chirpmodemdemod and decode the
MAC frame (flags, base-40 callsigns, body) for get_packets.
Verified on the 2026-10-23 OTA capture (ota.cu8 -> .sdriq, FileInput):
49/49 frames, identical to cm_rx in order, source and body; last-frame SNR
and offset match (-10.1 dB, -2651.5 Hz, -11.86 ppm).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
libiio 1.0 is new and not yet packaged by distributions, so keep the
0.x API as the default and add ENABLE_LIBIIO_V1 (default OFF) to build
against 1.x explicitly.
The finder used to look for the 1.x header in IIO_DIR and in the system
paths before falling back to 0.x, independently of where it found the
library. With 1.x installed system-wide and IIO_DIR pointing at 0.26,
it combined 1.x headers with the 0.26 library and the link failed. Now
each candidate install (IIO_DIR, then the one pkg-config reports, then
the system paths) must provide both the header and the library for the
requested API; an install with the other API is skipped with a message.
Changing ENABLE_LIBIIO_V1 triggers detection again in an existing build
directory.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Explicitly select normalized install() DESTINATION path behavior
introduced in CMake 3.31. This removes redundant path components
such as "." from install destinations while preserving their
installation locations and reduces warnings on Windows-x64 builds.
Signed-off-by: Robin Getz <rgetz503@gmail.com>
FFTW3F is required unconditionally on Linux, but was only searched
for when ENABLE_EXTERNAL_LIBRARIES was AUTO. With ENABLE_EXTERNAL_LIBRARIES
set to ON, FFTW3F was neither found as a system library nor built as
an external dependency, resulting in build failures.
Find the system FFTW3F package when external libraries are explicitly
enabled on Linux.
Signed-off-by: Robin Getz <rgetz503@gmail.com>
Allow ccache usage to be disabled through the ENABLE_CCACHE CMake
option, while preserving the existing automatic detection and
Emscripten exclusion behavior.
This is useful for builds where ccache is available but undesirable,
(like Coverity) and provides clear configuration messages when
ccache is skipped.
Signed-off-by: Robin Getz <rgetz503@gmail.com>
Add a CMake cppcheck module that provides a new "make cppcheck" target
for running cppcheck against the project and generating a html report.
Use compile_commands.json for analysis, ensure generated Qt sources exist
before analysis, support project suppressions and parallel execution, and
generate an HTML report when cppcheck-htmlreport is available.
Cppcheck remains optional and is only required when BUILD_CPPCHECK is
enabled.
Signed-off-by: Robin Getz <rgetz503@gmail.com>
Modernize deprecated CMake usage and correct package-name mismatches
reported by newer CMake versions. Replace exec_program() with
execute_process(), use PkgConfig through find_package() while retaining
fallback discovery, and align find_package_handle_standard_args() names
with their corresponding find_package() calls.
This removes most CMake developer warnings without changing the intended
dependency discovery behavior.
Signed-off-by: Robin Getz <rgetz503@gmail.com>
PR #2775 merged the MeshCore plugin source files but omitted the
parent CMakeLists.txt changes, the export.h API macro, and all
MeshCore-specific Swagger schema types. Without these the plugins
do not build and the REST API serves Meshtastic types for MeshCore
channels.
Adds:
- CMakeLists.txt parent directories + option definitions
- exports/export.h MODEMMESHCORE_API macro
- MeshcoreDemod/Mod swagger YAML specs + SWG client classes
- SWGChannelSettings/Report/Actions/ModelFactory MeshCore types
- Rename 164 Meshtastic donor references in plugin code
Unix OSes that aren't Linux (e.g., BSDs) sometimes use /usr/local as
the prefix for non-system libraries. This is change is necessary to
build on at least FreeBSD, as libunwind is in /usr/local/lib, not
/usr/lib.