- **IQ**: auto make I/Q balance. The DC correction must be enabled for this to be effective.
<h4>2.1: Auto corrections</h4>
<h3>3: Carrier shift from center frequency</h3>
This combo box control the local DSP auto correction options:
Use this control to set the offset of the carrier from the center frequency of reception.
- **None**: no correction
- **DC**: auto remove DC component
- **DC+IQ**: auto remove DC component and correct I/Q balance.
<h3>4: Decimation factor</h3>
<h4>2.2: Decimation factor</h4>
The I/Q stream from the generator is doensampled by a power of two before being sent to the passband. Possible values are increasing powers of two: 1 (no decimation), 2, 4, 8, 16, 32. This exercises the decimation chain.
<h3>5: Baseband center frequency position relative the center frequency</h3>
This exercises the decimation chain.
<h4>2.3: Baseband center frequency position relative the center frequency</h4>
Possible values are:
@ -59,44 +62,60 @@ Possible values are:
@@ -59,44 +62,60 @@ Possible values are:
- **Inf**: the decimation operation takes place around the center of the lower half of the BladeRF Rx passband.
- **Sup**: the decimation operation takes place around the center of the upper half of the BladeRF Rx passband.
This exercises the decimation chain.
<h3>6: Sample rate</h3>
This controls the generator sample rate in samples per second.
<h3>7: Sample size</h3>
<h3>2.4: Sample size</h3>
This is the sample size in number of bits. It corresponds to the actual sample size used by the devices supported:
This slider controls the number of amplitude bits by steps of 100 bits.
<h3>3: Sample rate</h3>
This controls the generator sample rate in samples per second.
<h3>4: Modulation</h4>
- **No**: No modulation
- **AM**: Amplitude modulation (AM)
- **FM**: Frequency modulation (FM)
<h3>9: Number of amplitude bits</h3>
<h3>5: Modulating tone frequency</h3>
This controls the modulating tone frequency in kHz in 10 Hz steps.
<h3>6: Carrier shift from center frequency</h3>
This is the signal peak amplitude in number of bits
Use this control to set the offset of the carrier from the center frequency of reception.
<h3>10: Amplitude fine control</h3>
<h3>7: AM modulation factor</h3>
This controls the AM modulation factor from 0 to 99%
This slider controls the number of amplitude bits by steps of 1 bit.
<h3>8: FM deviation</h3>
This controls the frequency modulation deviation in kHz in 100 Hz steps. It cannot exceed the sample rate.
<h3>11: Signal power</h3>
<h3>9: Amplitude coarse control</h3>
This is the signal power in dB relative to the maximum power (full bit range).
This slider controls the number of amplitude bits by steps of 100 bits. The total number of amplitude bits appear on the right.
<h3>10: Amplitude fine control</h3>
<h3>12: DC bias</h3>
This slider controls the number of amplitude bits by steps of 1 bit. The signal power in dB relative to the maximum power (full bit range) appear on the right.
<h3>11: DC bias</h3>
Use this slider to give a DC component in percentage of maximum amplitude.
<h3>13: I bias</h3>
<h3>12: I bias</h3>
Use this slider to give an in-phase (I) bias in percentage of maximum amplitude.
<h3>14: Q bias</h3>
<h3>13: Q bias</h3>
Use this slider to give an quadrature-phase (Q) bias in percentage of maximum amplitude.
<h3>14: Phase imbalance</h3>
Use this slider to give an quadrature-phase (Q) bias in percentage of maximum amplitude.
Use this slider to introduce a phase imbalance in percentage of full period (continuous wave) or percentage of I signal injected in Q (AM, FM).